![]() ![]() The command that we will write on the COMMVIEW is 12 00 0E 04ġ2 : command to read EEPROM (form 12H Read EEPROM)Ġ00E : start memory location for master codeĠ4 : need to send 4 bythe length because master code length is 4 byte (refer to the Memory Layout table mentioned above) To read master code, you can refer to “12H Read EEPROM” Commview software (download SOYALDeviceTool and obtain Commview)Ĭompatibility: SOYAL Home Series (H Series) Controller.Then you can enter programming mode by entering * 111111 # Modify the Master Code directly (ex.111111) Run “701 Server”, select the Controller Model - H/E series Controller Please confirm the controller is online before the following steps to change the Master Code, if you cannot connect the equipment correctly, please refer to 701Server Manual – Polling Mode Setting. The modification of Master Code of H/E series Controller by 701Server are the same method, using E series Controller as example below. SOYAL Enterprise Series (E Series) Controller The methods to connect your Controller to PC: RS485 to USB Converter AR-321CM, or TCP/IP Converter to connect PC This means you can enter programming mode by entering *123456# Once the Master Code is done resetting, the message box will shows “Completed!” > If you are using AR-727-CM ( RS485 to Ethernet converter) or AR-MDL-RJ45 you might select TCP/IP option and enter your IP address. > If you are using AR-321-CM converter ( RS485 to USB converter) you might select the correct COM Port option directly. If you do not know your current Node ID, entering “255” for auto research.Įven though the message box shows ‘Initial Failed’ you can still enter programming mode by default master code *123456#. Select target Node (Node ID), default Node ID is 1. Run ‘ISP Tool’, select the first option for H series controller ISP Tool software (download SOYALDeviceTool and obtain ISP Tool).Refer to the table below for more detail of what data to clean-up and what method is suitable for each Controller’s type. When you want to clean all of the controller’s data to factory reset, you can clean user data only, parameter setting only (incl. If you don’t want to factory reset or clean the memory, but forget what your current master code, you might want to either directly reset the master code, know what your current master code is, or directly change the master code. The Master Code default value for every Controller is 123456 and it is suggested to change the Master Code meticulously when installing the controller to avoid illegal access to Controller’s user data and parameter setting. To enter programming mode and to add card via keypad command or LCD menu, you need to know the Master Code or Programming Code of the Controller. Questions : How to change or reset different kinds of Controller Settings, including Master Code, Parameter Setting and User Data? Commview – Read current Master Code and Write new Master Code 701 Server – Overwrite with new Master Codeģ. Uninterruptible Power Supply Wall Mount Bracket License Plate Recognition IP Camera Power Supply Wiegand Keyboard LED Display BoardĢ.Peripherals / Accessories (Wiegand Keyboard/Power Supply/Wall Mount Bracket).Relay Output Module Ethernet Module POE Module Reader Module Voice Module Mifare Module Wiegand Reader Protection Board. ![]() Module (Relay/Ethernet/POE/Voice/Reader).Touchless Infrared Button Stainless Steel Push Button Door Sensor.Card / Keychain / Keyfob / Label Sticker.Electric Lock Purchasing Guideline Smart Digital Door Lock Electric Bolt Lock (Fail-Safe) Electric Bolt Lock (Fail-Secure) Electric Bolt Lock Accessories Electronic Magnetic Lock (Fail-Safe) Electronic Magnetic Lock Accessories Electric Strike (Fail-Secure) Cabinet Lock (Fail-Secure).TCP to RS485 Repeater USB to RS485 / RS485 to RS232 TTL to RS485 TTL to RS232.I/O Modules Purchasing Guideline I/O Module Series with Converter Function IP I/O Module Series Modbus RTU I/O Module Series. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |